Product display
Sine-cosine encoder EL-F5D8C series
Summary:
Classification:
Incremental Encoder
Related Documents:
- Summarize
- Technical data
- Related downloads
-
- Commodity name: Sine-cosine encoder EL-F5D8C series
This product is used for angle, length measurement, and positioning control in industrial systems.
1. Overview
1.1 Manual Instructions
This manual mainly describes product information. For operational safety, please read the manual carefully before operating the device!
In addition, local accident prevention regulations and general safety rules must be followed.
1.2 Warranty Statement
Warranty period is 18 months, calculated from the delivery date.
2. Transportation and Storage
2.1 Transportation and Unpacking Safety Instructions
Professional transportation packaging (packaging boxes, etc.) is used. Do not throw, impact, or fold.
2.2 Transportation Inspection
Upon receipt, please immediately check whether the delivery contents are complete and whether there is any transportation damage. If damage is found:
- Do not accept the goods or accept them only under the condition of reserving the right of recourse;
- Record the extent of the damage on the shipping documents or delivery note;
- Immediately file a complaint.
2.3 Storage
Storage should meet the following conditions:
- Keep dry and dust-free;
- Do not expose to corrosive media;
- Avoid mechanical impact.
3. Product Features
3.1 Applications
This product is used for angle, length measurement and positioning control in industrial systems.
4. Product Information
4.1 Product Selection
4.2 Dimensional Drawing
Figure 1 Installation Size Diagram (Unit: mm)
4.3 Technical Data
Supply Voltage
DC5±0.25V
Current Consumption
<100mA
Resolution
2048
Response Frequency
100KHz(Max)
Output Signal
A, B, R, C, D
Output Waveform
Sin/Cos
Differential Voltage
1Vpp±0.1V
Offset Voltage
2.5±0.02V
Insulation Resistance
500MΩ(DC1000V)
Speed
6000r/min(Max)
Axial Load
20N
Radial Load
30N
Vibration Resistance
100m/S², 200Hz, 2h each in XYZ direction
Shock Resistance
100m/S², 10ms
Starting Torque
0.002N.M(Max 25℃)
Ambient Temperature
Operating: -25℃～85℃; Storage: -30℃～100℃
Ambient Humidity
95%RH
Protection Level
IP54
Weight
Approximately 204g
4.4 Output Circuit and Waveform
Signal Amplitude: Vp=0.45-0.6V
Signal Amplitude Offset: Ve=0.06V(Max)
R Signal Effective Threshold: Vr=0.25-0.8V
R Signal Cycle Width Tr=180°±90°
5. Installation and Removal Guide
5.1 Installation Guide
Figure 1 Installation Diagram
①: Use accessory 4MM hex wrench to unscrew the encoder top cover screws counterclockwise and remove the rear cover.
②: Push the encoder into the host mounting hole. After the tapered shaft and the tapered hole are tightly fitted, insert the accessory M5*50 bolt into the encoder tapered shaft, and use the accessory 4MM hex wrench to tighten it clockwise (tightening torque 5-5.5Nm) and fix it coaxially with the traction machine.
③: Use the accessory 2MM hex wrench to tighten the clamping ring tightening screw clockwise (tightening torque 0.6-0.8Nm) so that the clamping ring is tightly fitted and fixed to the traction machine body.
Note: After the encoder is installed, connect the matching cable to the encoder wiring terminal, Confirm the direction and press slowly. After the cable is installed, tighten the encoder rear cover with screws and press the cable shielding part.
5.2 Removal Guide
Figure 2 Removal Diagram
①: Use the 4MM hex wrench accessory to loosen the encoder cover screws counterclockwise and remove the cover. Unplug and remove the encoder cable.
②: Use the 2MM hex wrench accessory to turn the clamping ring fastening screw counterclockwise to separate the clamping ring from the traction machine body.
③: Use the 4MM hex wrench accessory to rotate the M5 bolt inside the tapered shaft counterclockwise 1-2 turns.
④: Use the 4MM hex wrench accessory to turn the M10*20 stud bolt clockwise into the center hole of the encoder. After encountering resistance, forcefully tighten it to loosen the encoder. Remove the M10 stud bolt, then remove the M5 bolt and take out the encoder.
6. Connection Method
6.1 Wiring Port Definition
Pin
1a
2a
3a
4a
5a
6a
7a
Signal
C-
A-
0V
R-
B-
D-
VCC
Pin
1b
2b
3b
4b
5b
6b
7b
Signal
VCC
D+
C+
R+
0V
A+
C+
Contact Information
Changchun Shenghao Electronics Co., Ltd.
Company Exchange Tel: 0431-89543335 0431-89543336
Company Email: sh@ccshdz.com
Company Website: www.ccshdz.com
Company Address: B8, B9 Building, Phase 1, Beihubo Science and Technology Park, Beihubo Science and Technology Development Zone, Changchun, Jilin Province
-
Power Supply Voltage
DC5±0.25V
Current Consumption
<100mA
Resolution
2048
Response Frequency
100KHz(Max)
Output Signal
A、B、R、C、D
Output Waveform
Sin/Cos
Differential Voltage
1Vpp±0.1V
Bias Voltage
2.5±0.02V
Insulation Resistance
500MΩ(DC1000V)
Speed
6000r/min(Max)
Axial Load
20N
Radial Load
30N
Vibration Resistance
100m/S²，10ms
Shock Resistance
100m/S²，200Hz，XYZ方向各2h
Starting Torque
0.002N.M(Max 25℃)
Ambient Temperature
Operating: -25℃～85℃；Storage: -30℃～100℃
Ambient Humidity
95%RH
Protection Level
IP54
Weight
Approximately 204g
-
EL-F5D8C-0.55TSB220.48-AVV series instruction manual latest template.docx
Related Products
Product Consulting
Service Hotline:
Company switchboard:0431-89543335 0431-89543336
Sales Department:0431-80829999 0431-86071111
Department of International Trade:0431-89543339
Company E-mail:sh@ccshdz.com
Company address: Building B8, Phase I, Beihu Science and Technology Park, Beihu Science and Technology Development Zone, Changchun City, Jilin Province
Copyright: Changchun Shenghao Electronics Co., Ltd.
